Stran 2 od 2

Re: Asus n66u

Objavljeno: 23. Nov 2016 ob 23:49
Napisal/-a PatrikK
Mi je zalaufal GUI normalno... moram vseeno naredit?

Re: Asus n66u

Objavljeno: 23. Nov 2016 ob 23:59
Napisal/-a oyoy
ja, v vseh navodilih piše, da se po namestitvi tomata najprej počisti nvram, potem se ga začne konfigurirati. to imaš v nastavitvah tomata!

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 00:06
Napisal/-a PatrikK
Okkey, bom počistil. Je pa to moj prvi tomato fw upgrade :)

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 00:15
Napisal/-a oyoy
welcome :D
odkar sem pred leti namestil tomato na starega dobrega linksysa wrt54g, sva s tem fw postala nerazdružljiva prijatelja :mrgreen:

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 07:19
Napisal/-a PatrikK
oyoy: kaj so pa te verzije MultiWan od shibby-ja? Mogoče veš?

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 08:18
Napisal/-a oyoy
podpora za več isp-jev oz. več wan portov istočasno. če se ne motim, lahko definiraš do 4 wan porte. ampak to je samo opcijska nastavitev, tako da vsekakor priporočam zadnjo multiwan verzijo (tudi jaz redno posodabljam in imam vedno nameščeno zadnjo v.).
zdaj, ko imaš tomato že nameščen, nameščaš novo verzijo brez recovery mode, torej narediš klasični upgrade preko vmesnika. shibby tudi objavi, kdaj je potrebno pri oz. po nadgradnji počistiti nvram, navadno takrat, ko gre za spremembe pri driverjih.

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 18:36
Napisal/-a PatrikK
Aha, najlepša hvala za vse info. Bom zrihtal kar danes vse!


Edit: Še eno vprašanje. Sem opazil pri verzijah tomata, (K26RT-N – MIPSR2 in K26RT-AC) pri obeh je omenjen moj model routerja RT-N66U. Katerega naj izberem za najbolj optimalno delovanje?

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 21:36
Napisal/-a oyoy
razlika naj bi bila v verziji driverja - pri ac je novejši. menda pa starejši driver iz n builda zagotavlja boljšo pokritost ... :nevem:
the "regular" N66 build uses the 5.100 driver, while the AC build uses the 6.30 driver.
The (older) 5.100 will give you better wireless coverage than 6.30.

Re: Asus n66u

Objavljeno: 24. Nov 2016 ob 21:42
Napisal/-a PatrikK
Aha. Okkey, bom pustil staro verzijo gor. Naj bo, v končni fazi bi rad, da mi pokrije tudi zunanji del (teraso), za poletne dni :)

Re: Asus n66u

Objavljeno: 4. Mar 2017 ob 18:50
Napisal/-a PatrikK
Evo, danes sem dokončno flashla router z official firmwarom, tomato shibby in n66u ne gresta skupaj. Wifi signal prekinja nonstop.

Re: Asus n66u

Objavljeno: 4. Mar 2017 ob 20:12
Napisal/-a oyoy
Zanimivo ...
Če si se odločil za stock fw, bi ti predlagal Asuswrt-Merlin verzijo. Namesti se s klasičnim Upgrade Firmware preko GUI.

Re: Asus n66u

Objavljeno: 6. Mar 2017 ob 21:36
Napisal/-a PatrikK
Aha, bom, a moram nvram počistit pred flashanjem?

Re: Asus n66u

Objavljeno: 6. Mar 2017 ob 22:19
Napisal/-a oyoy
načeloma ne, če je na routerju org fw.
tole je iz merlin wiki-ja ( https://github.com/RMerl/asuswrt-merlin ... stallation );

You can download the firmware from http://asuswrt.lostrealm.ca/download.

Since Asuswrt-merlin is mostly a variant of the original Asuswrt, it means that there is no special procedure to flash it. Just flash it the same way you would flash any regular Asus firmware. A few notes:

Starting with Asus's 3.0.0.4.380_3000 and upward, a new firmware format is used. To flash Asuswrt-Merlin on one of these newer firmwares, you will need 380.61 or newer. Likewise, downgrading to an older version is not supported (try firmware recovery mode if you really need to downgrade)
The RT-AC68U and RT-AC56U need to be at least on firmware 378.55 (or the last 378.xxx version from Asus) before you can flash 380.xx, due to the partition size change.
It's recommended to reboot the router BEFORE flashing it, to free up sufficient memory. Otherwise, there's a chance the router might reject the firmware, due to running too low of free RAM.
If coming from a non-Asuswrt firmware, you will have to do a factory default reset.
While it is generally not necessary to restore to factory defaults, it's not a bad idea, especially if there is a big jump in version number (from 112 to 178 for example). No need to do the 30/30/30 dance as required by DD-WRT - just do a plain Factory Default reset, or turn the device on while keeping the WPS button pressed (procedure can be different from one model to another).
It is very hard to brick an Asus router. If something goes wrong during flashing, you can put your router in Recovery mode by powering it on while you keep Reset pressed. After your release it, the power LED will either blink or stay off (depending on the model). At that point, you can either access it through http://192.168.1.1 (make sure you first set your PC on a static IP within the same range, i.e. 192.168.1.100 for example), or through the Firmware Recovery Tool provided on Asus's support CD. You will then be able to flash a working firmware.
If something looks weird, don't waste too much time: save your settings, reset to factory default, reconfigure the basics, and see if the issue is resolved. If not, you can always restore your saved settings, and do some more advanced troubleshooting.
It is NOT recommended to restore settings saved under a different firmware version. It might work, but there is no guarantee.